• HPPE 47.4%, Polyester 20.1%, Glass Fibre 17.2%, Steel 14%, Spandex 1.3%.
• Food Safe and washable.
• Extremely high cut protection.
• Suitable for general food preparation and areas where high cut protection is needed.

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level F - TDM Cut Resistance (ISO 13997)

• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)

• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)

• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)

• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)

• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)

• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)

• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)

• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)

• Premium Cowhide Split Leather
• G-150gram Thinsulate and Micro Fleece
• Nylon Cuff

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 3 - Tear Resistance
• Level 4 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)

• EN 511:2006
• Level 1 - Convective Cold Resistance
• Level 3 - Contact Cold Resistance
• Level X - Water Penetration

• 13 Gauge, HPPE Liner.
• 100% TPE Fully Injection coating.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level C - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection

• 13 Gauge, HPPE Liner.
• 100% TPE Fully Injection coating.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection

• Premium Grey split leather.
• Heavyweight cotton backing and safety cuff.
• Para-Aramid lining.

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 4 - Puncture Resistance
• Level E - TDM Cut Resistance (ISO 13997)

• Premium soft grain Leather.
• Natural Coloured backing.
• Half elastication to back of cuff.
• Para-Aramid lining.

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 4 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)

• Premium goatskin Leather with reinforced stitching
• Reinforced Para-aramid Lining
• ARC Flash resistant ASTM F2675/F2675M 41cal/cm2
• ARC Flash Heat attenuation factor 94.5%

• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 3 - Tear Resistance
• Level 3 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)

• EN 407:2004
• Level 4 - Burning Behaviour
• Level 1 - Contact Heat
• Level 2 - Convective heat
• Level 2 - Radiant heat
• Level X - Small splashes of Molten Metal
• Level X - Large splashes of Molten Metal

• Unique combination of mechanics-style backs with abrasion-resistant palms.
• Specially placed thermo-plastic rubber pads at back of hand protect against knocks without creating stiffness.
• Neoprene cuffs with hook and loop closure allow for ease of donning plus extra cushioning at the wrist.

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection

• Premium goatskin Leather with reinforced stitching
• Reinforced Para-aramid Lining
• Thinsulate lined layer
• ARC Flash resistant ASTM F2675/F2675M 56cal/cm2
• ARC Flash Heat attenuation factor 95.7%

• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)

• EN 407:2004
• Level 4 - Burning Behaviour
• Level 1 - Contact Heat
• Level 3 - Convective heat
• Level 2 - Radiant heat
• Level X - Small splashes of Molten Metal
• Level X - Large splashes of Molten Metal

• EN 511:2006
• Level X - Convective Cold Resistance
• Level 3 - Contact Cold Resistance
• Level X - Water Penetration

• High performance anti-vibration gloves
• Nylon/cotton knit with natural vulcanised palm and fingertips

• EN388: 2016
• Level 4 - Abrasion
• Level X - Cut Resistance
• Level 4 - Tear Resistance
• Level 2 - Puncture
• Level B - ISO 13997 Cut Resistance

EN10819:
Medium Frequency Spectrum "M" - 0.865 Pass
High Frequency Spectrum "H" - 0.598 Pass

• Para-Aramid 25.5, Steel 11%, Polyester 16.6%, Polycotton 46% Liner.
• Latex palm Coating.
• Ventilated back.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)

• 15-gauge nylon liner
• Fully coated with latex
• Water resistant
• Dry/wet grip

• EN388: 2016
• Level 2 - Abrasion
• Level X - Cut Resistance
• Level 4 - Tear Resistance
• Level 1 - Puncture
• Level A - ISO 13997 Cut Resistance

• Powder Free black textured Nitrile Gloves
• CE category III
• Excellent elasticity
• Textured for added grip

Chemical - Breakthrough Time
n-Heptane(J) - More than 30 Mins (level 2).
Sodium Hydroxide 40%(K) - More than 480 Mins (level 6).

Additional Chemical Test
Ammonia 25% - More than 10 Mins (level 1).
Formaldehyde 37%- More than 480 Mins (level 6).
Hydrogen Peroxide 30% - More than 480 Mins (level 6).

• EN420: 2003 +A1:2009
• EN 374-2: 2014
• EN 374-3: 2003

• HPPE 49%, Polyester 25%, Glass Fibre 12%, Steel 8%, Spandex 6% Liner.
• 100% Nitrile Rubber Coating
• 100% PVC TPR Back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)

• HPPE 40.9%, Nylon 14.1%, Polyester 15.9%, Glass fibre 21.3%, Spandex 7.8% Liner.
• 100% Nitrile Rubber Coating.
• 100% PVC TPR back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)

• Para-Aramid 71.2%, Steel 13.5%, Polyester 10.5%, Spandex 8% Liner.
• 100% Nitrile rubber coating.
• Ventilated back.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 1 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)

• 13 Gauge, HPPE, Polyester, Glass Fibre Green Liner.
• 100% Sandy Nitrile Coating
• 100% TPR Back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 3 - Puncture Resistance
• Level C - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection

• 13 Gauge, HPPE, Polyester, Glass Fibre Orange Liner.
• 100% Sandy Nitrile Coating
• 100% TPR Back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 3 - Puncture Resistance
• Level C - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection

• 13 Gauge, HPPE, Polyester, Glass Fibre Green Liner.
• 100% Foam Nitrile Coating
• 100% TPR Back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.

• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection

• 13 Gauge, HPPE, Polyester, Glass Fibre Orange Liner.
• 100% Foam Nitrile Coating
• 100% TPR Back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.


• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection