Glovezilla
GLOVEZILLA - HIGH PERFORMANCE HAND PROTECTION
HPPE 47.4%, Polyester 20.1%, Glass Fibre 17.2%, Steel 14%, Spandex 1.3%.
Food Safe and washable.
Extremely high cut protection.
Suitable for general food preparation and areas where high cut protection is needed.
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 2 - Puncture Resistance
Level F - TDM Cut Resistance (ISO 13997)
100% Para-Aramid Liner.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 1 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 2 - Tear Resistance
Level 3 - Puncture Resistance
Level B - TDM Cut Resistance (ISO 13997)
EN ISO 11612: 2015
A1 - Limited Flame Spread (Method A)
F2 - Contact Heat (250C for between 10 to 15 Seconds)
100% Para-Aramid Liner.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 1 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 2 - Tear Resistance
Level 3 - Puncture Resistance
Level B - TDM Cut Resistance (ISO 13997)
EN ISO 11612: 2015
A1 - Limited Flame Spread (Method A)
F2 - Contact Heat (250C for between 10 to 15 Seconds)
100% Para-Aramid Liner.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 1 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 2 - Tear Resistance
Level 3 - Puncture Resistance
Level B - TDM Cut Resistance (ISO 13997)
EN ISO 11612: 2015
A1 - Limited Flame Spread (Method A)
F2 - Contact Heat (250C for between 10 to 15 Seconds)
100% Para-Aramid Liner.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 1 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 2 - Tear Resistance
Level 3 - Puncture Resistance
Level B - TDM Cut Resistance (ISO 13997)
EN ISO 11612: 2015
A1 - Limited Flame Spread (Method A)
F2 - Contact Heat (250C for between 10 to 15 Seconds)
Premium Cowhide Split Leather
G-150gram Thinsulate and Micro Fleece
Nylon Cuff
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 3 - Tear Resistance
Level 4 - Puncture Resistance
Level B - TDM Cut Resistance (ISO 13997)
EN 511:2006
Level 1 - Convective Cold Resistance
Level 3 - Contact Cold Resistance
Level X - Water Penetration
13 Gauge, HPPE Liner.
100% TPE Fully Injection coating.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 3 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 2 - Puncture Resistance
Level C - TDM Cut Resistance (ISO 13997)
Level P - Impact Protection
13 Gauge, HPPE Liner.
100% TPE Fully Injection coating.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 3 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 2 - Puncture Resistance
Level D - TDM Cut Resistance (ISO 13997)
Level P - Impact Protection
Premium Grey split leather.
Heavyweight cotton backing and safety cuff.
Para-Aramid lining.
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 4 - Puncture Resistance
Level E - TDM Cut Resistance (ISO 13997)
Premium soft grain Leather.
Natural Coloured backing.
Half elastication to back of cuff.
Para-Aramid lining.
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 4 - Puncture Resistance
Level D - TDM Cut Resistance (ISO 13997)
Premium goatskin Leather with reinforced stitching
Reinforced Para-aramid Lining
ARC Flash resistant ASTM F2675/F2675M 41cal/cm2
ARC Flash Heat attenuation factor 94.5%
EN 388:2016+A1:2018
Level 3 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 3 - Tear Resistance
Level 3 - Puncture Resistance
Level D - TDM Cut Resistance (ISO 13997)
EN 407:2004
Level 4 - Burning Behaviour
Level 1 - Contact Heat
Level 2 - Convective heat
Level 2 - Radiant heat
Level X - Small splashes of Molten Metal
Level X - Large splashes of Molten Metal
Unique combination of mechanics-style backs with abrasion-resistant palms.
Specially placed thermo-plastic rubber pads at back of hand protect against knocks without creating stiffness.
Neoprene cuffs with hook and loop closure allow for ease of donning plus extra cushioning at the wrist.
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 3 - Puncture Resistance
Level B - TDM Cut Resistance (ISO 13997)
Level P - Impact Protection
Premium goatskin Leather with reinforced stitching
Reinforced Para-aramid Lining
Thinsulate lined layer
ARC Flash resistant ASTM F2675/F2675M 56cal/cm2
ARC Flash Heat attenuation factor 95.7%
EN 388:2016+A1:2018
Level 3 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 2 - Tear Resistance
Level 3 - Puncture Resistance
Level D - TDM Cut Resistance (ISO 13997)
EN 407:2004
Level 4 - Burning Behaviour
Level 1 - Contact Heat
Level 3 - Convective heat
Level 2 - Radiant heat
Level X - Small splashes of Molten Metal
Level X - Large splashes of Molten Metal
EN 511:2006
Level X - Convective Cold Resistance
Level 3 - Contact Cold Resistance
Level X - Water Penetration
High performance anti-vibration gloves
Nylon/cotton knit with natural vulcanised palm and fingertips
EN388: 2016
Level 4 - Abrasion
Level X - Cut Resistance
Level 4 - Tear Resistance
Level 2 - Puncture
Level B - ISO 13997 Cut Resistance
EN10819:
Medium Frequency Spectrum "M" - 0.865 Pass
High Frequency Spectrum "H" - 0.598 Pass
Para-Aramid 25.5, Steel 11%, Polyester 16.6%, Polycotton 46% Liner.
Latex palm Coating.
Ventilated back.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 3 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 2 - Puncture Resistance
Level D - TDM Cut Resistance (ISO 13997)
15-gauge nylon liner
Fully coated with latex
Water resistant
Dry/wet grip
EN388: 2016
Level 2 - Abrasion
Level X - Cut Resistance
Level 4 - Tear Resistance
Level 1 - Puncture
Level A - ISO 13997 Cut Resistance
Powder Free black textured Nitrile Gloves
CE category III
Excellent elasticity
Textured for added grip
Chemical - Breakthrough Time
n-Heptane(J) - More than 30 Mins (level 2).
Sodium Hydroxide 40%(K) - More than 480 Mins (level 6).
Additional Chemical Test
Ammonia 25% - More than 10 Mins (level 1).
Formaldehyde 37%- More than 480 Mins (level 6).
Hydrogen Peroxide 30% - More than 480 Mins (level 6).
EN420: 2003 +A1:2009
EN 374-2: 2014
EN 374-3: 2003
HPPE 49%, Polyester 25%, Glass Fibre 12%, Steel 8%, Spandex 6% Liner.
100% Nitrile Rubber Coating
100% PVC TPR Back of hand protection.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 2 - Puncture Resistance
Level D - TDM Cut Resistance (ISO 13997)
HPPE 40.9%, Nylon 14.1%, Polyester 15.9%, Glass fibre 21.3%, Spandex 7.8% Liner.
100% Nitrile Rubber Coating.
100% PVC TPR back of hand protection.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 2 - Puncture Resistance
Level D - TDM Cut Resistance (ISO 13997)
Para-Aramid 71.2%, Steel 13.5%, Polyester 10.5%, Spandex 8% Liner.
100% Nitrile rubber coating.
Ventilated back.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 1 - Puncture Resistance
Level D - TDM Cut Resistance (ISO 13997)
13 Gauge, HPPE, Polyester, Glass Fibre Green Liner.
100% Sandy Nitrile Coating
100% TPR Back of hand protection.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 3 - Puncture Resistance
Level C - TDM Cut Resistance (ISO 13997)
Level P - Impact Protection
13 Gauge, HPPE, Polyester, Glass Fibre Orange Liner.
100% Sandy Nitrile Coating
100% TPR Back of hand protection.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 4 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 3 - Puncture Resistance
Level C - TDM Cut Resistance (ISO 13997)
Level P - Impact Protection
13 Gauge, HPPE, Polyester, Glass Fibre Green Liner.
100% Foam Nitrile Coating
100% TPR Back of hand protection.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 3 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 3 - Puncture Resistance
Level B - TDM Cut Resistance (ISO 13997)
Level P - Impact Protection
13 Gauge, HPPE, Polyester, Glass Fibre Orange Liner.
100% Foam Nitrile Coating
100% TPR Back of hand protection.
Lightweight for maximum dexterity and comfort with sensitivity.
Suitable for general assembly handling and engineering applications.
EN 388:2016+A1:2018
Level 3 - Abrasion Resistance
Level X - Cut resistance (Coupe Test)
Level 4 - Tear Resistance
Level 3 - Puncture Resistance
Level B - TDM Cut Resistance (ISO 13997)
Level P - Impact Protection